Mackie Network Card OPT 24 User Manual

OOPPTT2244  
OPT•24  
OOPPTT2244  
Installation Guide  
24-Channel 24-bit ADAT Optical I/O Card for the HDR24/96 and MDR24/96  
 
4) Remove the blank cover plate for the ACC1 slot (next to the SYNC card) by removing 1 Phillips-  
head screw. Save the screw for installing the OPT•24.  
4) Remove Screw and  
ACC1 Slot Cover Plate  
REAR PANEL  
®
5) Unplug the 2 ribbon cables from the Sync card. Squeeze the tabs on the sides of the connectors and  
gently wiggle from side to side to release them from their sockets.  
5A) Unplug Ribbon Cables  
from Sync Card  
5B) Pull Ribbon Cables back  
and out of the way  
REAR PANEL  
©
2 0 0 0  
M
®
3
Installation Guide  
 
6) Unplug both ends of the COM cable (040-383-00), located between the front panel Display board (A)  
and the Card Cage board (B). Cable ties hold the COM cable in place. Leave the cable inside the  
HDR24/96 in case the OPT•24 is ever removed and the COM cable needs to be reconnected.  
6) Remove the COM Cable  
from the Display Board (A)  
and the Card Cage Board (B)  
REAR PANEL  
©
2 0 0 0  
M
®
B
A
7) Connect the 2 short/fat ribbon cables (supplied) to the 2 bottom connectors (J3B and J4B, furthest  
from the edge) on the OPT•24. The connectors have a keying tab in the center so they can’t be  
plugged in wrong. It doesn’t matter which end of the ribbon cables you connect to the OPT•24.  
J3B  
J4B  
8) Connect the 2 ribbon cables that you removed from the Sync card to the 2 top connectors (J3A and  
J4A, closest to the edge) on the OPT•24. They will click in place when properly inserted.  
8) Connect 2 Ribbon Cables  
to OPT¥24 Board  
REAR PANEL  
OPT¥24 Board  
I
4
 
9) Install the OPT•24 into the ACC1 PCI slot by carefully aligning the cards gold-plated connector  
edge to the PCI slot on the motherboard and pushing down gently but firmly until the card is fully  
seated into the slot. It may help to gently rock the board front to back until the board is completely  
seated.  
Note: Make sure the loose connector ends are pointing up so they can be accessed for step 11.  
9) Install OPT•24 Board  
into the ACC1 PCI slot  
10) Install Screw into  
the OPT•24 bracket  
REAR PANEL  
I
®
10) Install the screw that you removed from the blank cover plate to secure the OPT•24 to the HDR chassis.  
11) Connect the short ribbon cables from the OPT•24 card to the adjacent Sync card by folding them over the  
top of the Sync card (see illustration below and on next page).  
11) Connect the 2 short ribbon  
cables to the Sync Card  
REAR PANEL  
®
5
Installation Guide  
 
Front view of ribbon cable connections between the  
Sync Card and the OPT•24  
12) Install the supplied replacement COM cable.  
a. Install the center connector to the Card Cage board.  
b. Install the shorter end to the front panel Display board.  
c. Install the longer end to the OPT•24 board.  
REAR PANEL  
12a) Install the replacement COM Cable:  
Center connector to Card Cage Board  
12c) Longer end to  
OPT•24 Board  
®
12b) Shorter end to Front  
Panel Display Board  
13) Replace the cover, reinstall the screws, and  
you’re ready to go!  
6
OPT•24  
 
Selecting the OPT•24 I/O  
This is done in the same way that you setup and  
configure the other I/O cards—in the Digital I/O  
Setup window (or by pressing the Digi-I/O button on  
the front panel).  
To select the OPT•24 from the front panel:  
1. Press Digi-I/O to enter the Digital I/O Card  
Setup screen.  
To select the OPT•24 from the screen  
(HDR24/96 only):  
1. Select Setup from the Windows menu and  
click the Digital I/O icon. The Digital I/O  
Setup dialog box shows you the current  
settings for each of the three I/O cards.  
DISK UTIL SYSTEM DIGI-I/O  
SYNC  
DEC  
2. Select In. The Setup Tape Inputs screen  
shows you the current settings for each of the  
three I/O cards.  
DIGITAL I/O Card Setup  
Stat Rate  
In Out Bits Convert  
3. Press the Select button corresponding to each  
I/O card and toggle the selection to the  
desired input source.  
4. The OPT•24 outputs are always active, so no  
configuration is necessary for the outputs.  
5. When done, press the Digi-I/O button to exit  
the menu.  
2. Click the Input pulldown menu and select the  
input source you want to use for each I/O  
card.  
3. The OPT•24 outputs are always active, so no  
configuration is necessary for the outputs.  
IN 17-24  
OUT 17-24  
IN 9-16  
OUT 9-16  
IN 1-8  
OUT 1-8  
“Mackie,” the “Running Man” figure, and “OPT•24”  
are trademarks or registered trademarks of Mackie  
Designs Inc. All other brand names mentioned are  
trademarks or registered trademarks of their  
respective holders, and are hereby acknowledged.  
OPT•24 Inputs and Outputs  
© 2002 Mackie Designs Inc.  
All Rights Reserved.  
Printed in the U.S.A.  
7
Installation Guide  
 
16220 Wood-Red Rd. NE • Woodinville, WA 98072 • USA  
US & Canada: 800/898-3211  
Europe, Asia, Central & South America: 425/487-4333  
Middle East & Africa: 31-20-654-4000  
 

Kyocera Fax Machine 2540 User Manual
La Crosse Technology Clock Radio WT 5600 User Manual
La Crosse Technology Portable Radio WS 9730U IT User Manual
Lennox Hearth Indoor Fireplace X FIRES 1000 LP User Manual
Lowrance electronic GPS Receiver IFINDER PRO User Manual
Magnasonic Digital Photo Frame 07MF117 User Manual
Makita Impact Driver 6936FD User Manual
Melissa Bread Maker 643 043 User Manual
Mellerware Fan 35220 User Manual
Mellerware Hot Beverage Maker 33010 User Manual